Jump to content

Fiacra

Members
  • Posts

    51
  • Joined

  • Last visited

Posts posted by Fiacra

  1. 1 hour ago, Bob229 said:

    Marks Models have the MM 121 loco decoder

    Thank you - completely missed that!

    2 hours ago, BEANO3005 said:

    Any decent 8 or 21 pin decoder will do. IRM and Murphy models recommended only using their decoders for warranty guarantees, but its over 12 months now since these locos were released. I use a mix of different decoders in my locos, and the only trouble I've had is with hornby 8 pin decoders. Lais dcc decoders are great value for money. I've used more that 30 so far over the last 5-8 years and all still going fine. 

    Hope this helps. 

    Thanks Beano. I'm very new to DCC and wasn't aware that generic decoders could be used - very helpful!

  2. Hi folks,

    I have been collecting Irish locos over the last couple of years, with a view to building a layout in due course. Unfortunately, at the time of buying the locos, I didn't give any consideration to DCC decoders - on the assumption that I would be able to pick them up at a later stage. Alas, not so. I've been able to find decoders for my 071 and 201, but it seems that A class and 121 decoders are out of stock everywhere. I'm assuming 141/181 decoders will be available when these locos are re-released, but does anybody know if the A class and 121 decoders are still available anywhere? Or, if they'll become available any time soon? Also, I should probably emphasise that it's only the decoders that I'm looking for, not the sound chips.

    Many thanks!

  3. 10 hours ago, TimO said:

    @Fiacra I took a few photos to show you what’s possible. This is a Murphy / Bachmann CIE coach from way back when, converted many moons ago to 21mm gauge, P4 Profile to run on Adavoyle. I think the wheels are Alan Gibson on 28mm axles and I suspect a jig was used to get everything square. Under the brass bolster plate there is a brass bush but the details are not visible. The screws are likely M2. the original bogie has just been cut down the centre and widened with the plate, nothing fancy. I hope this gives you some ideas.

     

    image.thumb.jpeg.221bb70032787b5b3d792ea2aeb9ea50.jpegimage.thumb.jpeg.c7c8f9da4b4532aab5319cf67ec936d4.jpegimage.thumb.jpeg.aa3a0bdb061b622d20640a995cc2348c.jpeg

    Lovely work! Very helpful - thanks TimO!

    • Agree 1
  4. Thanks TimO - that is very welcome news! I only have a couple of the original MM mk2d's and have been using them as conversion guinea pigs ahead of the new batch arriving. But, if the new bogies are prototype width, that will make things a lot easier.

    • Agree 1
  5. 20 hours ago, RedRich said:

    MJT Carriage Compensation Units can be assembled for EM P4 and 21mm. Brassmaster make nice units also.

    Thanks for this info Rich. The MJT rigid bogie frame was my first foray into brass kits, but despite my trepidation it was quite straight forward. However, CCUs look like they would require a much more delicate touch - might be a step too far for me at this stage. I'll pick one up though, and see how it goes. 

  6. Well, I'm in a position to answer the question myself now - it being 'with some difficulty'. There may be an easier way, but I ended up having to remove the body from the chassis, and even then, there was a lot of blindly poking, squeezing, and forcing the attachment jaws out of position, before the bogie came away. Clearly designed to be robust rather than for easy removal. I wonder if the new batch of mk2d's will be designed in the same way?

    My reason for wanting to remove the bogies in the first place is to regauge the models for EM track. I've mentioned this in a previous post, but I've opted to go EM gauge as a compromise between 00 and 21mm (the availability of track, points etc, being large part of the decision). Unfortunately, the bogies on the mk2d's are not wide enough for a simple axle swap-out. My original intention was to replace the whole bogie with an MJT brass bogie frame (using the original MM bogie sides as cosmetic attachments). Alas, it seems the MJT bogies are also strictly 00 gauge - something I only realised after constructing one and attempting to install a DCC Concepts EM gauge wheelset. That's no criticism of MJT, as they don't advertise the rigid bogie kits as anything other than 00 - I suppose I assumed there might be enough wiggle room in them to accept EM gauge axles.

    So, it looks like the only way forward is to cut up the MM bogies and use plasticard to rebuild them to a suitable width. That shouldn't be too difficult, but if anybody knows of another way of approaching this, I'm all ears.

    Many thanks! 

    • Like 2
    • Informative 2
  7. Apologies for such a basic question, but how does one go about removing the bogies from a MM mk2d? I thought they might disconnect with a bit of force, but that starts pulling the whole chassis away from the body, so it must require a more nuanced approach. 

    Thanks for any help!

    • Like 1
  8. 56 minutes ago, BosKonay said:

    The details are still placeholders, so only the header information is correct, in that case, its "5203 Irish Railways Mark 2d Standard - Irish Rail (Orange roof)" - everything else is placeholder information, pending any details from Mr. Murphy.

    Perfect - thank you!

  9. I received the 'ready to purchase' notifications for the mk2D's that I pre-ordered. However, I would like to get some clarification before I pay. The carriages are listed as e.g '5203 Irish Railways Mark 2d Standard - Irish Rail (Orange roof)', which I take to mean IR tippex livery with orange roof (exactly what I'm looking for). However, the description section for all of the 2D's states 'CIE Supertrain Livery'. Can anybody here shed any light on the matter?

    Many thanks!

  10. Apologies in advance for adding a very basic question to this thread. Am I correct to assume that a single 15v source can power multiple point motors (if they will only be thrown one at a time)? If this is the case, how should one go about connecting everything? Presumably it's not as simple as connecting all of the wiring directly to the power source. Is there such a thing as a breakout box that can receives the two wires from the power source, and can then relay this to multiple point motors?

    • Informative 1
  11. 1 hour ago, murrayec said:

    @FiacraA few photo of the motor mounting would help?

    If the motor is mounted directly under the points this could restrict movement as the actuation rod is short and cannot bend for short point movement! So if the motor is mounted with, say a 20mm thick mdf spacer between the motor and point, this would allow the actuating rod to bend a bit and allow the switch to operate correctly??

    Eoin.

    Thanks Eoin - this seems to be the most common solution to this problem. However, the actuating rod on these seep motors is fairly strong stuff - even cutting them takes a fair bit of effort. I'm not so sure it would bend even slightly, given the extra distance if mounted as suggested. I'll certainly give it a try though!

    27 minutes ago, Andy Cundick said:

    Its simple i used that setup for Lochty The trick with the SEEPs  is to convert the fixing holes into slots(file or burr)and don't tighten the screws just leave them slightly floating that way you have enough movement for the switch,Andy

    Ah, indeed - that sounds like just trick! Thanks Andy.

  12. Hi folks,

    Following on from a post I made last year regarding the possibility of modelling Irish railways in EM gauge, I decided to build a small test track consisting of a single, branching line (i.e. three lengths of track connected to a turnout) on which to test run some re-gauged rolling stock - dip my toes in the world of gauge conversion before committing to a full layout. I’m using an EM Gauge Society Peco turnout and I purchased a Gaugemaster PM-4 Seep point motor to control the switch rails and the polarity of the frog. Alas, I’ve already hit a bump in the road. It looks like the throw of the switch rails in the Peco turnout is considerably less than that of the point motor (and, presumably, of regular 00 gauge Peco turnouts). As a consequence, the contact at the base of the switch rod that would change the polarity of the frog can not move a sufficient distance to complete its job (i.e. it remains in contact with one of the polarity strips on the circuit board of the point motor, rather than disconnecting from one and then connecting to the other).

    So, either I am doing something very wrong (which is very possible) or these Seep point motors are not suitable for finescale turnouts. As there are a number of finescale modellers on this forum, I would be very interested to hear what point motors they use, and whether or not they have to make any modifications to get them working properly.

    Many thanks!

  13. On 16/11/2022 at 11:13 AM, Dave Dawes said:

    I ordered some Bullhead track last year and yes it was all very drawn out experience. Only just rejoined forum so only just noticed this post 

    Looks like that's going to be the case for me too. My order status has changed to 'paid' and I finally received an email last week to say there had been a delay in restocking some items. So, two months later and still waiting to receive anything. I suppose it's to be expected though - the producers of finescale items are probably very small operations. 

    • Agree 1
  14. 47 minutes ago, murphaph said:

    Longer top hat bushings are available I'm sure. As for the rotating axle boxes....not sure, how deep are they? Could they be sanded thinner?

    Bushings! Now that I know what they're actually called, I can search for them - thanks Phil.

     

    31 minutes ago, Brendan8056 said:

    Well done on making the move nearer to the proper gauge! Here is a link to a couple of articles in "New Irish Lines" about 21mm gauge diesel locos, including the 121 class. It is well worth subscribing to this magazine if you model Irish railways.

    https://www.dropbox.com/s/d86eqxk57ajch81/New Irish Lines Vol. 9 No. 3 - 2021 May.pdf?dl=0

    I was rather brutal with my 121 rotating hubs, to get clearance. When shortened I carefully glued them in place so they are now fixed. You have to have very good eyesight to see them rotate at normal viewing distance. I have had no problem with the extending of the wheels to the axle ends, the excess play does not seem to cause any problems.

    IMG_3548.JPG

    Thanks for this info Brendan - will definitely check out the articles in New Irish Lines. It did occur to me that the hubs could be trimmed and glued in place, but that seems such a shame when they were designed to rotate. Alas, it might be the only option. Regarding the side-to-side play, it's probably not so pronounced with 21 mm as the wheels are pushed out close to the bogie frame, which (together with the glued hubs) would presumably limit the side-to-side movement? I'll have a look around for longer bushings, as suggested by Phil, but otherwise it might actually be easier to bypass the EM trials and go straight to 21 mm!

    • Like 3
    • Agree 1
  15. Having thought about the pros and cons of 21 mm a bit more, I've decided to have a go at constructing a short length of 21 mm track and a couple of points, just to see what it entails - and I'll convert a 121 to run on it. Before that though, I thought I would ease into the whole conversion experience by first converting the 121 to EM and running it on some Peco EM bullhead track and a couple of kit-built EM points. And so I've arrived at my first bump in the road.......

    The attached photo shows a bogie on the 121 with the left wheel set re-gauged to EM (on original axle), while the right wheel set has not yet been re-gauged. What I've noticed is that there is now quite a bit of side-to-side play in the re-gauged wheel set due to the increased space between the wheels and the brass(?) rings that hold the axle in the gear block. This isn't an issue on the 16.5 mm wheel set because the wheels are tighter to the brass rings and this limits the side-to-side movement. Brass rings (whatever they're actually called) with a longer cylinder would seem to be the obvious solution - or some type of spacer that can be put on the axle between the wheel and the brass ring. Does anybody know if such items are readily available? 

    Another thing I noticed is that when the wheels are spaced for 21 mm gauge on the original axle, the outside face of the wheel is almost flush with the end of the axle. This leaves no room at the end of the axle for the rotating hubcap to slide on to it. Has anybody found a way around this?

    As always, thanks for any input!

    IMG_1129.jpg

    • Like 2
    • Informative 1
  16. Hi folks, 

    Have any of you had problems ordering from C & L? I placed an order via their website in mid-September and got confirmation from my bank that the payment went through a couple of days later. However, my order status is still showing as 'awaiting payment/awaiting processing' on the C & L website. Have sent a couple of emails, but no response. My understanding is that C & L is a one-man operation, but still, this seems like an unusually long time. Anybody else had a similar experience? 

  17. Was looking out the window of my house here in Oughterard (Co. Galway) a minute ago and, quite unexpectedly, saw a brake van on the back of truck pass by! Presumably on its way out to the crew at Maam Cross?

    • Like 3
  18. 23 minutes ago, Andy Cundick said:

    The trouble is EM still doesn't look right,i've got layouts in both EM and 21mmespecially when it comes to steamers where you have the wheels peeking out behind the splashers.AS for bogies just use the MJT bogies which can be readily built to 21mm gauge and use the side  frames off the original bogies as a cosmetic overlay.Andy.

    Thanks for that suggestion Andy. I wasn't aware of the MJT bogies, but just checked them out and they don't seem overly complicated to construct. I take your point on EM still not looking right - I suppose I would be settling for something that looks 'less wrong' than 16.5 mm. However, those bogies are now making me consider going P4 instead of EM, which would look less wrong again 🙂  I know it might seem pointless to go to all the effort of P4 conversions rather than going to the full 21 mm, but the matter of pointwork construction for the latter still terrifies me!

  19. 1 hour ago, murphaph said:

    I don't think any tools exist for Irish EM. No back to back gauges, roller gauges etc. They would need to be custom made for such an endeavour.

    With straight 21mm between the rails you can get most of these tools from the Scalefour society's stores, with the exception of a back to back gauge. I think they do an Irish gauge one but it's for P4 wheels so it's too wide to use for regauging typical 00 wheelsets.

    John Mayne made a solid brass back to back up for me and EDM models have a nice 3d printed one which I also have. These work fine for regauging RTR wheels from IRM to "full" 21mm.

    Sorry for diverting your thread Fiacra. It's your railway of course so whatever you decide is right at the end of the day.

     

    Not at all Phil - grateful for all input on the matter! I think there are two main issues putting me off going the 21 mm route, despite the layout being solely Irish outline - pointwork and re-gauging rolling stock. The planned layout will have around 18 points in total (including the fiddle yard), and building all that from scratch seems quite daunting - not just the actually construction, but doing it to a standard that ensures reliable running. With EM or P4, there are ready-to-lay or easily assembled turnout kits available on the market. On the re-gauging side of things, my understanding is that converting to EM is, usually, fairly straight forward. Sometimes it's possible to re-space wheels on their existing axel, but failing that, drop-in wheel sets are readily available - perhaps needing only a slight sanding of the inner side of the bogie to create sufficient space. With P4 and 21 mm gauges, considerably more re-building of bogies is required to accommodate the wider wheel sets. I know this is not an issue with the Murphy Models and IRM locos, which were designed to accept 21 mm wheel sets, but that doesn't seem to be the case for the MM MkIID and Cravens that I've procured. That being said, if the new run of MkIID will have wider bogies ready to accept 21 mm wheel sets, that could have an influence on the matter. Similarly, if IRM have any new coaching stock announcements coming up, that might also help sway my opinion 😉 

    • Like 1
×
×
  • Create New...

Important Information

Terms of Use